Industry News

The negative pressure suction system of the Isuzu vacuum tanker truck is its core component. This system generates strong negative pressure through decompression, quickly sucking waste into the storage tank. At the same time, after being processed by the filter, solid particles and liquids will be effectively separated to ensure that the discharged waste will not cause secondary pollution to the environment. Pumps can transport waste to off-site treatment facilities for further processing or disposal. In this way, Isuzu vacuum tanker truck can not only complete waste collection and cleaning efficiently and quickly, but also reduce the spread of waste pollution, fundamentally protecting the environment and improving the quality of life. A.Main operating systems of Isuzu vacuum tanker truck and maintenance of sewage suction trucks: ①．Pneumatic reversing valve of sewage suction truck. ②. Power take-off lever. ③. Vacuum pump. ④. Manual reversing valve. ⑤. Four-way valve. ⑥. Oil and gas separator. ⑦. The sewage suction truck tilts the cylinder and opens the door cylinder. ⑧, dump ball valve, drainage ball valve. ⑨. Sewage suction truck tank door locking device. ⑩. Sewage suction hose and alarm. 1. Precautions for the conveyor: Before operating theIsuzu vacuum tanker truck, check whether the transmission shaft, directional coupling shaft, etc. are abnormally shaking or loose. If the defective parts are not repaired and the work is carried out, it will have adverse consequences on major devices such as pumps and power take-offs. 2. Oil and gas separator of Isuzu vacuum tanker truck (for vacuum pump lubrication) The separated engine oil can be reused as vacuum pump lubricating oil, but the separated water will be stored at the bottom of the tank, so it must be drained after the operation of the sewage suction truck. If you forget to drain, it will Suction into the pump can cause problems such as sintering. If the oil is used for too long, the lubricity and air tightness will be reduced. Therefore, the interior should be cleaned regularly and the lubricating oil should be replaced. When the vacuum degree is about 93 kPa, the oil level should be replenished to the middle mark under the dipstick. Use HT-40# mechanical oil and clean the interior once a month. 3. Isuzu vacuum tanker truck one-way valve water and gas separator. When the automatic suction stop device in the Isuzu vacuum tanker truck tank is full and malfunctions, it is a device that automatically works to prevent sewage from entering the pump of the Isuzu vacuum tanker truck. If it sucks in sludge with a lot of oil content, it will easily corrode the ball seat and the ball. In addition, it is easy to accumulate sewage during operation, so the float must be drained and cleaned after the operation. 4. Clamping device for the rear tank door of the Isuzu vacuum tanker truck. After long-term use, dirt will occur inside and the hand wheel must not be tightened. Ther...

Garbage disposal is an important part of modern urban management, and Isuzu compression garbage trucks, as an important equipment for garbage disposal, have the advantages of high efficiency, energy saving, and environmental protection. This article will introduce the working principle of a compression garbage truck to better understand its working process. 1. Composition of Isuzu compressed garbage truck.  The Isuzu compressed garbage truck mainly consists of a body, a compression device, a garbage bin and a control system. The car body is the basic structure of the garbage truck, the compression device is the core component for garbage compression, the garbage bin is used to store garbage, and the control system is used to control the operation and compression process of the garbage truck. 2. Working principle.  2-1. Garbage loading stage: When the Isuzu compressed garbage truck starts working, it first places the garbage bin at a specific location, and then opens the feed opening of the garbage bin. The garbage loader then loads the garbage from residential households or garbage sites into the bins. During the loading process, the garbage loader will evenly distribute the garbage within the garbage bin to ensure uniform compression of the garbage. 2-2. Garbage compression stage: When the garbage bin is full, the compression garbage truck starts to compress the garbage. First, the control system will start the compression device to compress the loaded garbage. The compression device is usually driven by a hydraulic system, and the compression plate is moved into the garbage bin through a hydraulic cylinder to compress the garbage. During the compression process, the compression plate will gradually move toward the compression chamber to compress the garbage into a smaller volume. 2-3. Garbage transportation stage: After the garbage compression is completed, the compression garbage truck will close the garbage bin and install it on the vehicle body. Then the garbage truck starts transporting garbage. Compressed garbage trucks are usually equipped with a power system that allows them to drive themselves to a waste treatment plant or transfer site. During transportation, the garbage bins are kept closed to prevent the scattering of garbage and secondary pollution. 2-4. Garbage unloading stage: After arriving at the garbage treatment plant or transfer station, the compressed garbage truck will unload the garbage bin. During the unloading process, the garbage truck will open the bin and dump the garbage through the dumping device into the garbage disposal equipment or transfer vehicle. After unloading is complete, the bins will be reinstalled on the garbage truck, ready for the next round of garbage disposal. 3. Summary. Isuzu compressed garbage trucks achieve efficient waste processing through stages such as garbage loading, garbage compression, garbage transportation and garbage unloading. Its working principle mainly relies on the coope...

The Isuzu sewage tanker truck is a high-end special vehicle specially designed for cleaning and absorbing liquid or semi-solid waste. Known for its powerful suction power and efficient filtration system, the sewage suction truck is able to quickly extract and store all kinds of dirt, sludge, waste water and other substances. As an important tool for environmental cleaning and pollution prevention, sewage tanker trucks play an important role in many fields. However, there will be many people who are eager to know the production process of Isuzu sewage tanker trucks, let's take a closer look.   The main process flow of the tank: blanking->forming->welding->non-destructive testing->assembly,welding->non-destructive testing->pressure test A. Material selection and cutting (1) Principles of material selection for containers： 1.Has sufficient strength, plasticity, toughness and stability. 2.It has good hot and cold processability and welding performance. 3.Equipment in corrosive media must have good corrosion resistance and hydrogen resistance. (2) Cutting tools and trial scope: 1. Gas cutting: carbon steel 2. Plasma cutting: alloy steel, carbon steel 3. Shearing trigger: &≤8㎜ L≤2500㎜ Cutting edge is straight edge 4. Sawing machine: pipe, channel steel 5. Plate rolling machine: three rollers (3) Materials： Q235A Q345A ordinary low carbon steel B. Process flow Head: Material purchase -> Material preparation -> Marking and cutting -> Edge planing -> Forming -> Flanging -> Chamfering -> Inspection Tank door: Material purchase—>material preparation—>marking and blanking—>edging—>forming—> flanging—> marking and opening—>welding flanges and pipe joints—>inspection Tank body: Material purchase—>Blanking—>Grinding—>Rolling—>Tailor welding—>Inspection—>Rounding C.The main process flow of frame assembly:blanking - > assembly - > welding - > inspection Blanking tools and trial scope:    1. Gas cutting: carbon steel   2. Plasma cutting: carbon steel 3. Shear trigger: &≤12mm L≤2500mm trimming edge is a straight edge   4. Sawing machine: pipe, round bar Blanking material material: Q235A                         

With the continuous acceleration of urbanization, the problems of urban garbage disposal and transportation have become increasingly prominent, which has led to the widespread application and promotion of Isuzu rear-loading compression garbage trucks. Rear-loading compression garbage trucks have the advantages of high reliability and large carrying capacity, which provide a strong guarantee for the harmlessness, reduction and resource utilization of urban garbage treatment. 1. Market demand. Urban waste disposal is an important issue in urban management, and waste removal is a crucial part of it. The fast, efficient and safe garbage removal is the reason why Isuzu rear-loading compression garbage trucks are widely introduced. At present, the urban waste treatment industry has formed a large scale, but there are still some problems, such as backward treatment facilities and equipment, irregular management, and low technical level of transportation vehicles, which have brought troubles to urban waste treatment. Isuzu rear-loading compression garbage trucks are efficient, safe and fast as garbage removal vehicles, and meet the needs of the urban waste treatment industry for garbage removal. 2. Product advantages. Isuzu rear-loading compression garbage trucks have many advantages over traditional garbage removal vehicles. First of all, the rear-loading compression garbage truck has a larger carrying capacity and can effectively improve the efficiency of garbage removal. Secondly, this product uses a compressed trash can, which can reduce the volume of garbage and further reduce the volume and weight of garbage. Third, the rear-loading compression garbage truck adopts a closed compression device, which can effectively prevent garbage from leaking, dripping, flying and seeping, ensuring the cleanliness and freshness of the urban environment. Finally, the product uses automation technology to improve the efficiency and quality of manual work and ensure driver safety. 3. Innovative technology. The advanced technological application of Isuzu rear-loading compression garbage trucks can significantly improve the efficiency and quality of garbage removal. On the one hand, the product adopts an intelligent control system, which can automatically complete operations such as garbage compression, filling, cleaning, and transfer; on the other hand, the product's appearance design, transmission system, car chassis and garbage compression system technology are all adopted Advanced technology is used to achieve greater effect improvement and ensure the efficiency and convenience of garbage removal. 4. Competitive Landscape. As the Isuzu rear-loading compression garbage truck market continues to develop, competition in the market has become increasingly fierce. However, this product has advanced technical advantages and high-quality performance in the market, and its market share will increase in the future. At the same time, this product will dev...

Isuzu hook-arm garbage truck, also known as removable compartment garbage truck and pull-arm garbage truck. This vehicle is widely used for garbage disposal in urban streets and schools. One vehicle can be equipped with multiple buckets, and multiple garbage buckets can be placed at each garbage point. It has a self-unloading function and is hydraulically operated for easy dumping. 1. Overview. The box part of the Isuzu hook-arm garbage truck is completely controlled by the hydraulic system. On weekdays, the truck-mounted garbage can can be placed at various garbage collection stations. After the garbage is collected, the truck can drive directly to the garbage station through the hydraulic system. With the control, you can lower the hook arm installed on the back seat of the garbage truck, hook it to the connection point at the front end of the garbage bin in the station, and pull the garbage bin to the back seat of the vehicle body. At this time, you can start the vehicle and transport the garbage to In the garbage disposal station, self-unloading dumping is carried out. The main advantage of this vehicle is that one vehicle can be equipped with multiple buckets, and one vehicle can maintain the operation of several garbage collection stations. It is highly efficient, and the box is of sealed design, which will not cause secondary pollution. 2. Structure. The Isuzu container-type detachable garbage truck, also known as the pull-arm garbage truck (hereinafter referred to as the garbage truck), is a special vehicle used for the collection, transportation and unloading of bagged and bulk domestic garbage in cities and towns. The vehicle is composed of a car chassis, a pull arm main cylinder, an attached frame, a flip frame, a supporting leg (optional), a locking frame, a locking cylinder and a multi-way reversing valve. One end of the flip frame is connected to the attached frame, and the other end is equipped with a movable pull arm, with a locking system installed in the middle; one end of the movable arm cylinder is connected to the movable arm, and the other end is connected to the attached frame; the locking mechanism passes through the lock The action of the tightening cylinder can integrate the box on the attached frame with the flip frame and the pulling arm when the box is self-unloading, forming a self-unloading angle when the main oil cylinder is extended. It can also be turned over by retracting the locking oil cylinder. The frame and the attached frame are locked as one, and the retraction or extension of the main oil cylinder is used to make the movable pulling arm drag the underground garbage bin to the attached frame or put it back to the ground from the attached frame. The vehicle can pull the garbage and garbage bins in the underground garbage bin to the vehicle for transportation and can also self-unload, reducing the labor intensity of workers. The garbage collection and transportation method of this garbage truck is ...

Isuzu compressed garbage trucks will make precise calculations based on the pressure and flow required by the hydraulic system, and determine the specifications of cylinders, valves, pumps, etc. Selection, installation and design are realized through different calculations. 1. Control analysis and flow chart design When calculating the rated pressure in the hydraulic system of the Isuzu compressed garbage truck, the loading compartment is lifted to a certain position and then returned with a delay. At this time, it can ensure that all the garbage inside the compartment is dumped cleanly, and when the push plate is used for unloading , the filling compartment must be opened first and then dumped, otherwise the dumping cannot be completed. The scraper of the rear-mounted compression garbage truck swings out or the rear proximity switch is turned on to lower the skateboard. This realizes the filling cycle. If there are stones, metal hard objects, etc. in the garbage and the filling is overloaded, it is likely to cause a compression cycle. 2. Choose an appropriate electrical control system When selecting a control system for Isuzu compressed garbage trucks, an integrated multi-circuit solenoid valve is used to configure the electronic control system to achieve sequential control. The start and stop action signals are sent out through the electric button, and then the electronic control method is divided into two main forms. The electronic control method of the first type realizes relay control by detecting the end point and starting point of the cylinder. In addition, a PLC programming control system is selected. Since there is a certain logical relationship between relay circuits, and these systems also need to be controlled through hardware wiring, when comparing the reliability of the two, PLC control appears to be more reliable. 3. Control loop design As an important part of the electrical design, the Isuzu compressed garbage truck control circuit involves the manipulator circuit, scraper and skateboard circuit, push plate circuit, etc. The manipulator loop control is a sequential action, which can be effectively formulated in the structural design of the manipulator. The design is used as a linkage manipulator, and it is composed of cylinder drive and motion-completed garbage loading. These do not need to be controlled in the corresponding sequence. The circuit design between the scraper and the skateboard is such that the garbage is loaded from less to more, and from loose to tight. During this period, the load often fluctuates greatly. When formulating the scraper and skateboard circuit plan, two sequence valves can be used together, and a one-way hydraulic lock can be equipped in the scraper cylinder oil circuit. When designing the push plate circuit, the main purpose is to highlight its role as a chopping board for garbage compression. It is required that the push plate can be pushed forward and backward in the compression direction. This re...

With the continuous advancement of technology, Isuzu rear-loading compression garbage trucks have undergone great reforms, gradually transforming from the previous manual control to the current automated control. The wide application of pressure relays and electromagnetic steering valves in hydraulic systems allows the corresponding electrical systems to form an automated control mechanism, providing support for the automated control operations of Isuzu garbage trucks. Overview of electrical design principles of Isuzu garbage truck control system 1. Process connection and limit protection A limit switch was added to the electrical design of the garbage truck control system, and its position is at the action position of the skateboard and scraper. The limit switch installed here is mainly to detect whether the circuit is connected during the working stage, and to select the output signal through the controllable programmer to ensure that the garbage truck stops changing actions when the scraper and skateboard collide with other parts. , thereby reducing noise and avoiding serious mechanical damage caused by large-movement collisions. 2.Control method The control methods of garbage trucks in the electrical control system mainly include manual and automatic methods. Among them, manual control is basically when the filling mechanism is stuck by a large object or other unexpected situations occur, and manual switch button operation is often selected. Manual operation can reversely operate the scraper to make it move in the opposite direction, thereby freeing the filling mechanism from stuck objects. Normally, garbage trucks are operated automatically. Only when an unexpected situation occurs or the tail box is too full of garbage, the garbage is loaded into the garbage truck through short cycle operation to prevent the garbage from being pushed out. Main hydraulic control systems and component selection 1.Hydraulic steering valve When selecting a steering valve, sufficient research must be conducted, and then a suitable hydraulic steering valve must be selected based on the actual production conditions. Operators often undertake high-intensity labor during operations and have high requirements for system reliability. Two control modes, manual and automatic, are designed for direction control. When selecting a hydraulic steering valve, choose a combined form of steering valve. The valve core is equipped with a manual control machine operating handle, and is also equipped with a solenoid valve and a small cylinder. The cylinder is then controlled by controlling the solenoid valve, and the cylinder pushes the valve core. 2. Fuel tank The oil tank is mainly used for oil storage, and then ensures that the hydraulic system can fully operate the oil, and also has a corresponding heat dissipation effect. The oil tank also has the function of precipitating pollutants that have penetrated into the oil, thereby ensuring that the oil in the entire system is clean...

Isuzu sewage suction truck equipped with a powerful pump system that creates suction to draw the sewage into a tank mounted on the truck. The tank is designed to hold a large volume of liquid waste safely and securely during transportation.Isuzu sewage pump trucks are commonly used by municipalities, sanitation departments, and waste management companies to maintain and clean sewer systems, septic tanks, and other areas where liquid waste accumulates. They play a crucial role in maintaining public health and safety by preventing sewage backups and ensuring proper waste management. 1. Before inhaling the Isuzu sewage suction truck, prepare to close the rear door of the tank of the isuzu sewage suction truck and observe whether the lubricating oil of the vacuum pump oil and gas separator is normal. 2. Operation sequence: a. Depress the clutch pedal, push the power take-off lever to run the vacuum pump of the Isuzu sewage suction truck, and then slowly release the clutch pedal. b. Turn on the Isuzu sewage suction truck alarm switch in the cab. c. Pull the throttle handle to the maximum position, observe the tachometer, and make it reach 500-600 rpm (it has been adjusted at the factory). d. Place the four-way valve switching handle in the suction position, and check whether the air discharged from the trachea is correct, whether there is any sound when the vacuum pump is running, and whether the vacuum gauge is normal. e. Remove the sewage suction hose from the Isuzu sewage suction truck and put it into the sediment well. In order to keep the sewage suction hose in a straight line or freely bent state, the parking position should be fully considered. 3. Precautions for suction operation of Isuzu sewage suction trucks: a. Stones larger than 50mm, cotton yarn, leaves and other impurities will block the straw. So do not inhale and remove frequently. b. When the vacuum gauge reading reaches 65-80 kPa, fully open the ball valve of the sewage suction truck. The half-open state can easily damage the valve core. When inhaling sludge, the suction pipe should be moved frequently. When inhaling high-viscosity sludge, occasionally inhaling air and water can improve the pollution efficiency. 4.Method for discharging sewage from the sewage pumping truck: After the mud and water are separated, open the drainage ball valve, drain the sewage and repeat the suction of mud. You can also pressurize and drain quickly. The operation method is as follows: a. Place the four-way valve switching lever in the "neutral" position, and then place the drainage ball valve in the "open" position to drain sewage reliably by gravity. b. Switch the four-way valve of the Isuzu sewage suction truck to the discharge position, and the vacuum pump continues to work, and the compressed air sewage flowing into the tank will be quickly discharged. c. When draining pressure, the discharge ball valve should be opened first, and then the four-way ball valve can be moved to the discharge position ...

Isuzu sewage suction truck is a special type of vehicle used for the collection and transportation of sewage, waste water, and other liquids from various sources such as drainages, septic tanks, and other similar places. It is designed with a tank at the rear of the vehicle, usually made of steel or other durable materials, which is capable of holding a large volume of liquid. Isuzu sewage suction truck is equipped with a powerful vacuum pump system that creates a vacuum to suck up the sewage and liquid waste into the tank. Isuzu sewage suction trucks are typically used by municipal authorities, waste management companies, and sanitation departments to maintain clean and hygienic environments. 1. Maintain the appropriate rotational speed of the vacuum pump of the Isuzu sewage suction truck: If the vacuum pump rotational speed is too high, the rotor will heat up. If the rotational speed is too low, it will cause engine knocking and cause additional shock to the components, which will affect the service life. At the appropriate working speed, adjust the maximum adjustment of the hand throttle in advance. Sewage suction truck pump type xd-44 is suitable for rotation speed of 500-600 rpm. 2. The isuzu sewage suction truck is hydraulically lifted and dumped on flat ground. Isuzu sewage suction trucks are strictly prohibited from hydraulically lifting and dumping on sloping roads. If they are hydraulically lifted and dumped on sloping roads, the uneven road surface will cause the weight of the vehicle body to tilt to one place, causing distortion and deformation of the components there, and easily causing a rollover accident. 3. When hydraulically lifting the isuzu sewage suction truck, open the rear door window first. The rear door of the tank should be opened before hydraulic lifting to unload sludge. It is strictly prohibited to hydraulically lift the tank body of the isuzu sewage suction truck before opening the rear door of the tank, because the center of gravity will shift backward after lifting, which may cause the risk of overturning. 4. When taking power from the clutch oil pump and vacuum pump power take-off of the isuzu sewage suction truck, the driver should control the accelerator, make the engine idle, and fully step on the clutch pedal. After hooking up the power take-off to take power, the driver should slowly release it. Clutch pedal. Do not hang up the power take-off without depressing the clutch, otherwise the power take-off gear will hit the running gearbox gear, causing damage to both gears. The power take-off lever of the Isuzu sewage suction truck must be placed in the middle position when the vehicle is driving. 5. Do not use isuzu sewage suction trucks to inhale or transport waste oil and dangerous goods. When entering or repairing the sludge tank of Isuzu sewage suction truck while the sludge tank is hydraulically lifted, support rods and safety stops must be used. When transporting sewage, a manual rear door tank clamping dev...

The garbage bin of the Isuzu compressed garbage truck is made of high-strength weather-resistant steel plates. The side plates use an integrated forming process, with an arc shape, solid structure, beautiful appearance, light weight, good stress resistance, and large loading capacity. The push shovel is composed of a rectangular tube frame and high-strength weather-resistant plate, with a streamlined pushing surface. It is not only lightweight in structure, but also can load materials smoothly and discharge materials cleanly and thoroughly. The filler is mainly composed of the filler assembly, sliding plate, scraper and other components. Each component adopts a beam plate or box structure with good stress. They are all made of high-strength weather-resistant steel plates, with a solid structure and light weight. The garbage is in a closed state during the compression, filling and transportation process, eliminating the phenomenon of garbage dust flying and odor drifting during the transfer process. The joint surface between the garbage bin and the filler is equipped with a special rubber sealing strip, and a hydraulic locking device is used to compress and seal for good sealing; the lower part is designed with a specially structured water tank for double protection, which effectively prevents sewage dripping and eliminates secondary pollution. . The whole vehicle adopts electro-hydraulic control valves and PLC programmable control system, which comprehensively utilizes the advantages of electronic control and hydraulic control. Through electro-hydraulic joint control, it effectively solves the interface problem between the hydraulic system and the electrical system and improves the reliability of use. When the Isuzu compressed garbage truck is operating, the engine power output is automatically controlled through the electronic throttle controller to ensure that the engine can automatically select acceleration and idle states under various operating conditions of the garbage truck, avoiding power loss and system heating, reducing fuel consumption, and being economical. Good sex. It adopts imported electro-hydraulic multi-way valve and PLC programmable controller for integrated control, and uses a logic loop to ensure that each operation instruction is executed in sequence, which reduces the failure rate, avoids accidents caused by misoperation, and improves reliability. An emergency stop button is set up to stop the garbage filling operation device in any state or position to ensure the safety of workers and equipment. The lifting cylinder is equipped with an explosion-proof valve to prevent the loader from descending when the oil pipe suddenly bursts. It is also equipped with a safety brace to ensure the safety of personnel during maintenance. It has two operating modes: automatic and manual. The operation control boxes are installed in the cab and the rear of the vehicle respectively, making it very convenient to use and operate. Different user...

Isuzu sewage suction trucks, also known as vacuum sewage suction trucks, are sanitation vehicles that use the principle of vacuum negative pressure to suck sewage. It's core component is the vacuum pump. There are generally two types of vacuum pumps used in sewage suction trucks: 1. Water ring vacuum pump: The water ring vacuum pump (we refer to it as the water pump) is divided into an air inlet and an exhaust port, a stator and a rotor (impeller), and the air inlet is connected internally with the sewage suction tank. The impeller is eccentrically installed on the stator or casing, and the pump body is filled with an appropriate amount of water (antifreeze can be installed in winter) as the working medium liquid. When the impeller rotates, the water is thrown to the wall of the pump body under the action of centrifugal force, forming a closed rotating water ring with a shape similar to the pump body and nearly the same thickness. At this time, a crescent-shaped space is formed between the impeller and the water ring to form a vacuum. And this space is divided by the impeller into several small cavities equal to the number of blades. During one working cycle of the impeller, the volume of the small cavities in the first half of the cycle increases from small to large, and is connected to the suction port on the end face (inside the sewage suction tank) The gas is sucked in; in the second half of the cycle, the small cavity changes from large to small, and the gas is compressed. When the small cavity is connected to the exhaust port, the gas is discharged out of the pump. With the rotation of the impeller, the suction and exhaust process proceeds continuously and stably, so the gas can be continuously sucked, forming a negative pressure state in the suction tank, so that through the suction tank at the end of the suction tank. For example, the sewage is pumped into the sewage suction tank to achieve the purpose of sewage suction. 2. Rotary vane vacuum pump: Rotary vane vacuum pumps are also called oil pumps. The principle of this pump is similar to that of a water ring vacuum pump. Both vacuums are formed by compressed air, but the working environment is completely different. Water ring vacuum pumps are cooled by liquid, while rotary vane vacuum pumps are cooled by air. The rotary vane vacuum pump consists of an air inlet, an exhaust port, a rotor, and a rotary vane. The rotor is eccentrically fixed on the stator. There are grooves on the rotor for installing the rotary vane. The rotor can expand and contract radially according to the wall of the pump body cavity so that it can fit closely with the pump cavity. When force is applied, the eccentric rotor drives the rotary vane to slide close to the inner wall of the pump under the action of centrifugal force. The volume of the suction working chamber gradually increases in the first half of the cycle, and the pumped gas is sucked into it until the rotary vane rotates to the end of suction. , as the...

Isuzu sewage suction trucks are specifically designed to collect and transport sewage from various locations. They are equipped with a large tank and a powerful suction pump to efficiently remove and store sewage. Isuzu sewage suction trucks are commonly used by municipal authorities, sanitation departments, and cleaning services for sewer cleaning and maintenance tasks. 1. How to clean Isuzu sewage suction truck？ Isuzu sewage suction trucks are mainly used to clean urban sewers, pipeline sediments, clear mud ditches in dead corners, clean industrial drainage pipes, walls, etc. After being used for a long time, it is necessary to clean the sewage suction trucks. So how to clean the sewage suction trucks? To clean the Isuzu sewage suction truck, you need to use a special car wash place. Choose a ventilated and cool place, and use a car wash towel to scrub the body. During the cleaning process, you should pay attention to the following major items: A. Do not clean the sewage suction truck frequently to avoid damaging the paint of the sewage suction truck. B. Use clean water when washing your car, otherwise the fine sand in the sewage will wipe the car paint. If the temperature is low throughout the day, wash with warm water. C. Use a clean, dedicated car wash. Generally, towels have strong friction and can easily damage the stain-absorbing car paint. Especially after washing the car, you should wipe off the moisture on the car body immediately to avoid residual freezing and damage to the car paint. D. Wash your car in a ventilated and cool place. It is best to wash your car in a sunny place on a sunny day. E. When washing the car, pay attention to the waterproofing of certain parts of the sewage suction truck, such as horns, lights, door lock holes, etc. To avoid horn failure. The door lock cannot be opened if the light becomes foggy or water enters the winter door lock hole. F. Do not wash the sewage suction truck immediately after driving in winter. Before washing the car, you should wait until the engine temperature of the sewage suction truck drops to prevent thermal expansion and contraction from damaging the engine. 2. How to maintain Isuzu sewage suction trucks？ In order to extend its service life, in addition to paying attention to regular cleaning, other aspects of maintenance and upkeep should also be done. The main attention should be paid to the maintenance of sewage suction trucks: A. When the sewage suction truck is used for the first time, engine oil should be added to the pump. In low-temperature areas, antifreeze engine oil should be added. To ensure the normal operation of the sewage suction truck. B. The sealing ring of the rear tank door of the sewage suction truck should be cleaned after work. If there is leakage, the sealing ring of the rear tank of the sewage suction truck needs to be replaced to prevent the sealing ring of the rear tank door of the sewage suction truck from being used for a long time. resulting in reduced se...